Manufacturer:                                       PAMA, Germany

 

Year of manufacture:                           2004

 

Type of press:                                      Press with extended pressing zone JUMBO

Condition:                                          new press, never installed

Operating speed:                                  350 m / min

Linear pressure:                                    250 kN/m

Control of press:                                  hydraulic

Drive side along the paper web            left  

 

1. The supporting structure of press:

   – 2 pcs frames of press Material: carbon steel, galvanized

   (Including 2 pcs supporting and removable cushions for the installation of top roll Material: carbon steel, galvanized)

   Supporting stands – box section 360х300х4200 mm – 2 pcs

   Crossbeam between the frames of press – 4 pcs

   Longitudinal beam for mounting of felt guide rolls, showers and felt washers 220х220х3400 (4150) mm – 4 pcs

   Material: carbon steel

2. Top rubber-covered roll with blind holes, diameter of roll is 1250 mm, the length of the roll is 3650 mm, with journal elongated to drive, with bearing assemblies, pylons with a device for connection of the frame and a hydraulic cylinder

   Material: carbon steel

3.  Bottom rubber-covered roll with blind holes (diameter of roll is 1250 mm, the length of the roll is 3650 mm), with journal elongated to drive, with bearing assemblies and brackets for mounting the felt guide roll

   Material: carbon steel

    

4. Felt guide roll diameter 260 mm, the length of the roll 3700 mm, with bearing assemblies – 12 pcs

   Material: steel with rubber cover

    

5. Automatic felt guide for top and bottom felts – 2 set

 

 

 

 

– movable carriage with the actuator

– manual guide

– encoders

Material: carbon steel

 

1. Stretcher for top and bottom felts assembled with the synchronizing shaft and the drive – 2 pcs

   Material: carbon steel

2. Doctor for felt guide roll assembly with mounting brackets – 2 pcs

   Blades for doctor – 2 pcs

   Material: corrosion-resistant steel

3. Doctor for press roll assembly with mounting brackets with doctor pneumatic clamping device and with electromechanical drive of oscillation mechanism – 2 pcs

   Material: corrosion-resistant steel

4. Tube felt washer with mounting brackets, turning mechanism and connecting flange – 2 pcs

   Material: corrosion-resistant steel

5. Low pressure shower with mounting bracket and connecting branch, – 2 pcs

   Material: corrosion-resistant steel

6. High pressure shower with mounting bracket and connecting flange – 2 pcs

   Material: corrosion-resistant steel

    

7. Water collectors:

   – Water collector under felt washers for top and bottom felt with mounting brackets and drain pipe – 3 pcs

   Material: corrosion-resistant steel

        –    Water collector for bottom press roll – 1 pcs

           Material: corrosion-resistant steel 

1. Auxiliary equipment

• Tube with diameter 18 mm for hydraulic cylinders of press rolls– 25 pcs

  Material: corrosion-resistant steel

• Hydraulic nut for mounting roll bearings + Manual piston pump, thrust rings, pressure gauge, set of high pressure flexible hoses – 1 set

  Material: carbon steel

• Supports with separable consoles under bearing assemblies of felt guide rolls – 18 pcs

  Material: cast iron

• Console – support with separable console under bearing assemblies of felt guide rolls – 2 pcs

             Material: carbon steel

• The elongated tube for top press roll – 1 pcs

• Hydraulic cylinder assembly with mounting points to top press roll – 2 pcs

  Material: carbon steel

• Device for cantilevering of felt guide rolls – 1 pcs

  Material: corrosion-resistant steel

   

1. Mechanical drive for press rolls in the composition:

• The connection half-coupling between roll and cardan shaft –2 pcs

• Cardan shaft with half-coupling – 2 pcs

• The gearbox with helical gear with half-couplings – 2 pcs